- 您现在的位置：买卖IC网 > Sheet目录1234 > NCV73810V2GEVB (ON Semiconductor)BOARD EVAL FLEXRAY BUS NCV7381
NCV73810V2GEVB
USB Interface
Standard B type USB socket is used for connection to PC. USB interface is bus powered and electrically isolated from the
rest of the board, so it is not possible to supply this board via USB.
FlexRay CC Strobe Output Signals
The MCU FlexRay block provides a number of strobe
signals for observing internal protocol timing related signals
in the protocol engine.
These signals are connected to STBN pin header:
BDM Connector (MCU Debugging Interface)
The BDM module provides a single-wire communication
with host development system (Programming and
debugging interface).
FlexRay BD Digital Signals Test Points Headers
These headers are intended to be used as a test points for
digital probes. Headers contain all FlexRay BD digital input
and output signals.
Test points for both FlexRay channel A and channel B are
placed on separated headers (J73 – channel A,
J83 – channel B).
FlexRay BD Analog Signals Test Points
Each FlexRay channel contains 4 analog test points:
?
INH1 – Bus Driver Inhibit 1 output
?
INH2 – Bus Driver Inhibit 2 output
?
BP – FlexRay Bus Plus terminal
?
BM – FlexRay Bus Minus terminal
STBN1
STBN0
BKGD
NC
NC
GND
EN
TXEN
BGE
ERRN
J10
J83
STBN3
STBN2
GND
RESET
VCC
GND
TXD
RXD
STBN
RXEN
FlexRay Bus Connectors
FlexRay EPL Specification [1] does not prescribe certain connectors for FlexRay systems. Common used 9-pin D-Sub
connectors were chosen as a suitable connector, whose electrical characteristics satisfy the specification.
Table 1. FLEXRAY CONNECTOR
Pin #
1
2
3
4
5
6
7
8
9
Signal
?
FR_BM
FR_GND
?
?
?
FR_BP
?
(FR_Vbat)
Description
Reserved
BM Bus Line
Ground
Reserved
Reserved
Reserved
BP Bus Line
Reserved
Optional FR External Supply
Connection
Not Connected
BM
GND
Not Connected
Not Connected
Not Connected
BP
Not Connected
Main Supply Line
ESD Protection
Yes (Optional)
Yes (Optional)
Yes
Connector type: 9-pin D-Sub (DIN 41652 or corresponding international standard), plug (male)
http://onsemi.com
5
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
NF20AA0509MHL
CURRENT LIMITER INRUSH 5OHM 20%
NHD-4.3-480272MF-20
BOARD CTRLR FOR NHDEV 4.3 TFT
NHDEV DEVELOPMENT BOARD
BOARD DEV LCD COG TFT 100X95MM
NP0120TAT1G
IC PROTECTOR LOW CAP 12V 5TSOP
NP1500SCT3G
THYRISTOR TSPD 100A 150V SMB
NP2600SCMCT3G
IC TSPD SURGE DEVICE 150MA SMB
NP3100SBMCT3G
IC TSPD SURGE PROTECT 80A SMB
NP3500SCT3G
IC THY SURGE PROTECTOR 350V SMB
相关代理商/技术参数
NCV7381DP0G
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:FlexRay Bus Driver
NCV7381DP0R2G
功能描述:总线收发器 CLAMP 30 FLEXRAY TRANSC. RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel
NCV7382
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver
NCV7382/D
制造商:未知厂家 制造商全称:未知厂家 功能描述:Enhanced LIN Transceiver
NCV7382_07
制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Enhanced LIN Transceiver
NCV7382D
功能描述:IC TRANSCEIVER LIN ENH 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件
NCV7382DG
功能描述:IC TRANSCEIVER LIN ENH 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件
NCV7382DR2
功能描述:IC TRANSCEIVER LIN ENH 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件